Search
Search Results (3 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-99262 | 1 Linux | 2 Linux, Linux Kernel | 2026-11-04 | N/A |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. | ||||
| CVE-2026-99255 | 1 Linux | 2 Linux, Linux Kernel | 2026-11-03 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: io_uring/io-wq: don't hide a link from cancellations A task that exits cancels its tracked requests and waits until they are gone. io_uring_cancel_generic() looks everywhere a request can be, and goes to sleep if it found nothing to cancel. It is woken up each time one of the requests of the task is completed by task work or freed. When io-wq is done with a request that has a link, there is a time in which the next request of the link can't be found: io_worker_handle_work() io_assign_current_work(worker, NULL) io_wq_free_work(work) io_req_find_next() // takes the link off the request io_free_req() // task work for the task io_assign_current_work(worker, linked) io_run_task_work() cond_resched() worker->cur_work = linked It is not pending, it is not the current work of a worker, and it is not yet on the list that it is about to be parked on. If the pass that the exiting task makes because of io_free_req() falls into that time, it finds nothing and the task goes to sleep. The worker then runs the link, which IO_WQ_BIT_EXIT doesn't prevent for bounded work. If that parks the request nothing is completed or freed, and nobody wakes up the task. If it is the process that exits it can't be killed any more either. NOP, IOSQE_ASYNC | IOSQE_IO_LINK FUTEX_WAIT, FUTEX2_PRIVATE exit of the thread, or of the process, up to 63us later With four of these per round 5 to 8 of 10,000 rounds hang (4 CPUs, KVM): io_uring_cancel_generic do_exit Commit f8b632e89a10 ("io_uring: tighten task exit cancellations") is about the same gap, and makes the task look again for whatever happens before io_free_req(). Free the request once the link is the current work of the worker, or pending. Whoever is woken up by that can find the link, until it is parked where cancellations look as well. To do so split io_wq_free_work() in two. | ||||
| CVE-2026-89930 | 1 Linux | 1 Linux Kernel | 2026-10-30 | 9.3 Critical |
| In the Linux kernel, the following vulnerability has been resolved: KVM: nVMX: Service local TLB flushes on failed nested VM-Enter KVM services local TLB flushes on "full" nested VM-Exits (through __nested_vmx_vmexit()), but not if a nested VM-Enter fails (e.g. due to failed VMCS checks in nested_vmx_enter_non_root_mode()). However, it is possible that KVM had queued TLB flushes that need to be performed, even if the nested VM-Enter was not successful. For example, if VPID is disabled for L2 (via nested_vmx_transition_tlb_flush(), or if via the MSR load lists, as the SDM says: If any MSR is being loaded in such a way that would architecturally require a TLB flush, the TLBs are updated so that, after VM entry, the logical processor will not use any translations that were cached before the transition. The SDM is unclear about when the TLB flush should occur, and whether or not a failed VM entry would flush the TLB, so it is safer to always do the TLB flush in this case. More concretely, KVM also updates the last VPID L1 used for L2 in nested_vmx_transition_tlb_flush() (i.e. last_vpid), even if the VM entry ultimately fails. With the current code, KVM could miss a TLB flush if L1 changes L2's VPID, then does a failed VM entry followed by a successful one, as the failed VM entry would update last_vpid but not actually flush the TLB. Servicing local TLB flushes on failed VM entries makes sure that the TLB is always flushed when last_vpid is updated. | ||||
Page 1 of 1.